Back to overview

PVC-flat-CY

screened, EMC-preferred type

Technical data

Special PVC-flat cable, screened,
adapted to DIN VDE 0283-2
Temperature range
flexing -5°C to +70°C
fixed installation -40°C to +80°C
Nominal voltage
U₀/U 300/500 V
Test voltage
3000 V
Breakdown voltage
min. 6000 V
Minimum bending radius
15x cable thickness

Cable structure

Bare copper conductor,
fine wire acc. to
DIN VDE 0295 cl.5 / IEC 60228 cl.5
Core insulation of special PVC
Core identification see table below
Cores screened individually or in bunches
Copper screened braiding,
approx. 85% coverage
Outer sheath of special PVC
Sheath colour: black (RAL 9005)

Properties

Extensively oil resistant

Tests

Flame retardant acc. to
DIN VDE 0482-332-1-2 /
DIN EN 60332-1-2 / IEC 60332-1-2

Note

G = with GN-YE conductor
x = without GN-YE conductor
The conductor is metrically constructed
(mm²). The AWG designation is
approximate and purely informative.

Application

PVC screened flat cables are used mainly as trailing cable for crane installations, floor conveyer systems and shelf control units.
Installation notes
Cables reels with flat cables must be transported in standing position on the flange. A bending flexibility can be achieved on a plane surface. For this purpose, the corresponding fitting instructions should be followed.

Put the cable trolly on the guiding rail or upon carrier beam and push them together at the starting point. The distance between the bedding surface of two cable trollys must be wider than the double thickness of a cable-packet.
During the packeting performance, it must be started with the smaller cross section which lays on the bedding surface and will be builded successively so that the biggest cross section is laying on the top.
Further, be careful of a symmetrical load distribution.
In case of multicore flat cables with small cross section, smaller than 2,5 mm², is very critical due to its low tensile stress. In such case, you should add 10% reserve wire for calculation.

EMC = Electromagnetic compatibility
To optimize the EMC features we recommend a large round contact of the copper braiding on both ends.
CE = Product conforms with Low-Voltage Directive 2014/35/EU.

Downloads

Data sheet
Certificate of compliance

Part no.	No.cores x cross-sec. mm²	Core marking	Outer dimension approx. mm	Cop. weight kg / km	Weight approx. kg / km	AWG-No.
27100	5 G 0,5	Colour coded, DIN VDE 0293	21,0 x 3,4	64,0	140,0	20
27101	5 x 4 x 0,5	Colour coded, (blue, red, green, yellow)	37,4 x 7,2	175,0	280,0	20
27102	8 x 7 x 0,5	Cont. white numbering, DIN VDE 0293	68,6 x 11,7	480,0	1180,0	20
27090	4 G 0,75	Colour coded, DIN VDE 0293	15,0 x 5,0	70,0	147,0	19
26754	4 x 4 x 1	Colour coded, (blue, red, green, yellow)	33,5 x 11,0	310,0	625,0	18
27103	4 x 4 G 1	Cont. white numbering	33,5 x 11,0	310,0	625,0	18
27091	4 G 1,5	Colour coded, DIN VDE 0293	18,7 x 5,9	116,0	210,0	16
27092	8 G 1,5	Cont. white numbering	35,6 x 5,9	217,0	400,0	16
27093	12 G 1,5	Cont. white numbering	52,1 x 5,9	266,0	610,0	16
27094	4 G 2,5	Colour coded, DIN VDE 0293	21,0 x 6,9	170,0	270,0	14
27104	6 G 2,5	Cont. white numbering, DIN VDE 0293	37,4 x 7,2	240,0	320,0	14
27095	4 G 4	Colour coded, DIN VDE 0293	24,5 x 7,7	225,0	400,0	12
27096	4 G 6	Colour coded, DIN VDE 0293	30,1 x 9,2	328,0	520,0	10
27097