Back to overview

PVC-flat

300/500 V and 450/750 V

Technical data

Special PVC-flat cable in reference to
EN 50214 / DIN VDE 0283-2
Temperature range
flexing -5°C to +70°C
fixed installation -40°C to +80°C
Nominal voltage
up to 1 mm² U₀/U 300/500 V
from 1,5 mm² U₀/U 450/750 V
Test voltage
up to 1 mm² 2000 V
from 1,5 mm² 2500 V
Minimum bending radius
10x cable thickness

Cable structure

Bare copper conductor, to
DIN VDE 0295 cl.5, fine wire,
BS 6360 cl.5, IEC 60228 cl.5
Core insulation of PVC
compound type TI2 acc.to
DIN VDE 0207-363-3 / DIN EN 50363-3
Core identification to DIN VDE 0293
- up to 5 cores coloured
- from 7 cores, black with continuous
white numbering
Cores laying parallel
GN-YE conductor
Outer sheath of special PVC
compound type TM2 acc.to
DIN VDE 0207-363-4-1/DIN EN 50363-4-1
Sheath colour: black (RAL 9005)

Properties

Extensively oil resistant,
oil-/chemical resistance
see "Technical Information"
Extremely small bending radius
High flexibility
Minimum waste of space
Packeting possibility

Tests

Flame retardant acc. to
DIN VDE 0482-332-1-2 /
DIN EN 60332-1-2 / IEC 60332-1-2

Note

Part no. 27012 (6x4)
G = with GN-YE conductor
x = without GN-YE conductor
The conductor is metrically constructed
(mm²). The AWG designation is
approximate and purely informative.

Application

PVC type of flat cables are used mainly as trailing cable for crane installations, floor conveyer systems and shelf control units.
Installation notes
Cables reels with flat cables must be transported in standing position on the flange. A bending flexibility can be achieved on a plane surface. For this purpose, the corresponding fitting instructions should be followed.

Put the cable trolly on the guiding rail or upon carrier beam and push them together at the starting point. The distance between the bedding surface of two cable trollys must be wider than the double thickness of a cable-packet.
During the packeting performance, it must be started with the smaller cross section which lays on the bedding surface and will be builded successively so that the biggest cross section is laying on the top.
Further, be careful of a symmetrical load distribution.
In case of multicore flat cables with small cross section, smaller than 2,5 mm², is very critical due to its low tensile stress. In such case, you should add 10% reserve wire for calculation.

CE = Product conforms with Low-Voltage Directive 2014/35/EU.

Downloads

Data sheet
Certificate of compliance

Part no.	No.cores x cross-sec. mm²	Outer dimension approx. mm	Cop. weight kg / km	Weight approx. kg / km	AWG-No.
26980	4 G 0,75	4,3 x 12,6	28,8	90,0	19
26981	5 G 0,75	4,3 x 16,1	36,0	115,0	19
26982	6 G 0,75	4,3 x 19,4	43,2	141,0	19
26983	9 G 0,75	4,3 x 26,4	64,8	198,0	19
26984	10 G 0,75	4,3 x 30,1	72,0	224,0	19
26985	12 G 0,75	4,3 x 33,8	84,4	258,0	19
26986	16 G 0,75	4,3 x 44,4	115,2	340,0	19
26987	18 G 0,75	4,3 x 49,2	129,6	380,0	19
26988	20 G 0,75	4,3 x 55,0	144,0	424,0	19
26989	24 G 0,75	4,3 x 65,6	172,8	509,0	19
26990	3 G 1	4,5 x 10,8	28,8	80,0	18
26991	4 G 1	4,5 x 13,4	38,4	104,0	18
26992	5 G 1